Information reviewed: 16 November 2026

A basement project needs a coordinated picture of the existing building, surrounding ground and relevant neighbouring geometry. A measured survey supplies part of that picture. It does not replace ground investigation, structural design, drainage assessment or a Basement Impact Assessment. Our residential and basement survey service can be briefed around the information requested by the project’s engineers and planning advisers.

Basement courtyard survey — illustration
Illustrative view: basement courtyard survey.

Agree the engineering questions before capture

A generic floor plan may not show the relationships that matter below ground. Ask the engineer to identify critical section lines, level references, adjoining features and the external extent required. Where building and site data are commissioned together, agree one coordinate and level reference.

Information need Potential measured input Separate work that may be needed
Existing building geometry Plans, sections, visible levels and openings Structural assessment and investigations
Site levels Ground, thresholds, lightwells and accessible drainage features Drainage design and flood assessment
Neighbouring relationships Visible façades, levels and agreed accessible areas Legal access, party-wall advice and specialist assessment
Foundation or ground conditions Survey locations and levels for investigation records Trial pits, boreholes and geotechnical interpretation
Movement over time Agreed baseline reference and observation locations A designed monitoring programme with response thresholds

Scanning cannot reveal concealed foundation depth, soil parameters or groundwater conditions. If these appear on a coordinated drawing, their source and status should be identified.

Borough requirements are not interchangeable

Camden’s basement guidance addresses matters including groundwater, drainage, flooding and stability, with assessment and audit requirements depending on the proposal. Kensington and Chelsea publishes basement-specific supplementary guidance. Westminster’s application requirements can include structural and ground-related information, and its construction-practice requirements need separate consideration.

For Hammersmith and Fulham, check the adopted planning guidance and the current application validation requirements, including the relevant basement and lightwell provisions. Do not assume that a submission prepared for one borough is sufficient for another.

This guide was checked on 16 November 2026. The planning adviser should confirm the current policies, validation list, site designations and any Article 4 implications when the application is prepared. A measured survey quotation should identify which requested datasets it supplies, not promise an approved BIA.

Useful sections for a terraced-house basement

Consider a section linking the pavement or front area, ground floor, existing basement, rear threshold and garden. A second cut may be needed through the proposed excavation and adjoining structure. The correct locations depend on the design, so they should be marked by the responsible professional.

Neighbouring geometry may be only partly visible from permitted viewpoints. Record those limitations early. It is better to identify an unavailable level than to fill the gap with an apparently precise assumption that later drives an engineering decision.

The SW19 residential case and SW1X townhouse case show relevant measured-survey outputs. They do not establish that another site has the same ground conditions or permission requirements.

Basement neighbour model — illustration
Illustrative view: basement neighbour model.

Baseline recording is not the same as monitoring

A dated scan or condition record can document the starting point. Monitoring requires a repeatable method, stable reference, observation frequency and agreed response process. Those decisions should be set by the responsible specialist before works begin.

Do not compare two unrelated scans and assume any visible difference represents structural movement. Differences can arise from registration, viewpoint, surface conditions or changes to finishes. A monitoring specification should distinguish the change being investigated from the uncertainty of the measurement method.

Prepare a coordinated survey brief

  • Provide the address, proposal and current design sketches.
  • Include engineer-selected sections and critical levels.
  • Mark the required topographical extent and neighbouring context.
  • Identify access permissions, occupied areas and known hazards.
  • State the coordinate and level reference required by other consultants.
  • Distinguish measured geometry from ground investigation and condition work.
  • Agree the output files, checking requirements and delivery milestones.

Where external levels or drainage features matter, include topographical survey work explicitly. The party-wall records guide explains another related appointment that should not be confused with the measured survey itself.

Garden level survey — illustration
Illustrative view: garden level survey.

Frequently asked questions

Is a BIA always required for a London basement?

Requirements depend on the borough, site and proposal. Confirm the current local requirements with the planning adviser; a generic London-wide answer is unreliable.

Can the scanner find the foundations?

It can record exposed, accessible geometry. Concealed foundations require appropriate investigation, not ordinary surface scanning.

Can one visit cover every consultant’s needs?

It may cover the agreed accessible geometry if the requirements are coordinated in advance. Separate investigations and unavailable areas may need other visits. Send the engineering brief for a quotation.

References and review date

References checked on 16 November 2026. Requirements can change; confirm the applicable edition and project-specific requirements when appointing the team.